Ardupilot APM2.8 Flight Controller Combo

Ardupilot APM 2.8 Flight Control Board Bend Pin with Protective Case

Specification:
Item Name: APM 2.8 Flight Control Board

Features:
Arduino Compatible!
Includes 3-axis gyro, accelerometer, along with a high-performance barometer
Onboard 4 MegaByte Dataflash chip for automatic datalogging
Optional off-board GPS, uBlox LEA-6H module with Compass.
One of the first open-source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000.
Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively.

Description:
Receiver type: 72-channel u-Blox M8 engine
GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1
SBAS L1 C/A: WAAS, EGNOS, MSAS
Galileo-ready E1B/C (NEO-M8N)
Nav. update rate1 Single GNSS: up to 18 HZ
Concurrent GNSS: up to 10 Hz
Position accuracy: 2 2.0 m CEP
Acquisition2 Cold starts: 26 s
Aided starts: 2 s
Reacquisition: 1.5 s
Sensitivity2 Tracking & Nav: –167 dBm
Cold starts: –148 dBm
Hot starts: –156 dBm
Assistance AssistNow GNSS Online
AssistNow GNSS Offline (up to 35 days)3
AssistNow Autonomous (up to 6 days)
OMA SUPL & 3GPP compliant
Oscillator TCXO (NEO-M8N/Q),
Crystal (NEO-M8M)
RTC crystal Built-In
Noise figure On-chip LNA (NEO-M8M). Extra LNA for lowest noise figure (NEO-M8N/Q)
Anti-jamming Active CW detection and removal. Extra onboard SAW bands pass filter (NEO-M8N/Q)
Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N)
Supported antennas Active and passive
Odometer Travelled distance
Data-logger For position, velocity, and time (NEO-M8N)
Operating temp. –40° C to 85° C
Storage temp. –40° C to 85° C (NEO-M8N/Q), –40° C to 105° C (NEO-M8M)
RoHS compliant (lead-free)
Qualification according to ISO 16750
Manufactured and fully tested in ISO/TS 16949 certified production sites
Uses u-Blox M8 chips qualified according to AEC-Q100
Supply voltage 1.65 V to 3.6 V (NEO-M8M), 2.7 V to 3.6 V (NEO-M8N/Q)
Power consumption4 23 mA @ 3.0 V (continuous),5 mA @ 3.0 V Power Save Mode(1 Hz, GPS mode only)
Backup Supply 1.4 to 3.6 V
Features:
Quick satellite searching, only need 10s to find 6 satellite in open space
Built-in compasses, refresh rate up to 10GHz
0.6 meters ultimate accuracy, actually almost 0.9 meters, greater than the previous generation NEO-7N 1.4-1.6 meters accuracy
Support GPS+BD+SBAS, or GPS+GLONASS+SBAS
support GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol etc.

APM Pixhawk Power Module With XT60 and BEC

Specifications:
APM Pixhawk Power Module With XT60 is a simple way of providing your APM and Pixhawk with clean power from a LiPo battery as well as current consumption and battery voltage measurements, all through a 6-pos cable. The onboard switching regulator outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery. The Power Module comes completely assembled with Deans’ connectors, and wrapped in shrink tubing for protection.
Used to detect the battery voltage and the battery current, the flight control board receives two signals, calculates the remaining battery power, estimates the remaining flight time. In addition, the module also comes with a BEC function, you can output 5.3 DC, 3A maximum continuous current for the flight control board to provide a stable power supply. Another signal cable connector is used in Japan’s original fittings, non-domestic joint, so APM flight control board and reliable connection between the power supply module.

Voltage and current measurement configured for 5V ADC.
Switching regulator outputs 5.3V and 3A max.
6-pos DF13 cable plugs directly to APM or Pixhawk’s connector.
Note: The Power Module is only designed to power APM and Pixhawk’s, an RC receiver, and APM accessories (GPS, 3DR radio). It isnotdesigned to power servos. Use your aircraft’s own ESC/BEC for that.
The maximum input voltage 20V, maximum current measurable 90A, to achieve the control panel on battery power and voltage monitoring. The design parameters of voltage and current detector design parameters consistent with 3DR official ground station (mission planer) settings can be set directly refer to the official Wiki.

Type: Module
Accessory Type: Hobby Parts
Model: Hobby Parts
Max Input Voltage: 30V
Max Current Sensing: 90A
Size: 25mm x 21mm x 9mm/0.98″ x 0.83″ x 0.35″ (Approx.)

Package Included:

1 x AMP2.8

1 x  M8 GPS WITH COMPASS

1 x GPS Stand

1 x Shok Absorber

1 x Power Module